部分充满介质的理想螺线管条件

一般教科书中都提到，理想螺线管（指内部磁场均匀，无漏磁）的条件是无限长（相对而言），绕线蜂蜜。但对绕线是否应该均匀则未做详细论述。本文试图指出，在无介质情况下理想螺线管的绕线都是均匀的，但在部分充满介质的情况下，均匀的绕线反而会破坏“理想”的条件。     

ZrO_2纳米微粒红外振动特征

测定了单斜ＺｒＯ_２纳米材料在各种粒度下的付里叶变换红外光声光谱（ＦＴ—ＩＲ—ＰＡＳ），发现随粒度的减小，大部分的谱线位置蓝移，而有些谱线的位置红移，同时在不同频段，有的强度增强，有的强度减弱甚至消失。研究了量子尺寸效应和介电限城效应对其光学特征的影响，对观察到的物理现象进行了物理机制探讨     

微波与生物组织的相互作用及微波理疗中若干实际考虑

本文论述了描述微波与生物组织相互作用的数学表达式,讨论工作频率选择、透入深度、反射、极化、泄漏及防护等实际问题。     

Mechanism of Microwave Effects on Conductivity of Solution

The relation between microwave conductivity and normal conductivity of solution is compared in this thesis. By building mathematical model and theoretical analyses, it indicates that the relationship of in situ conductivity of solution in microwave field and temperature is similar to that in non-microwave field. It can be expressed by quadratic equation but the values of both conductivities are different. Microwave field has effect on the mean path δ or hot vibrational frequency v of ions in solution. In microwave field, the mean energy barrier, which ions must surmount as they transit, is the function relation to temperature.     

Joint Strength with Soldering of Al2O3 Ceramics After Ni-P Chemical Plating

Ni-P alloy was chemically plated on Al2O3 ceramics to produce uniform alloy coatings at temperatures below 70~C. Cu metal was electroplated onto the Ni-P coating to facilitate the soldering and shorten the chemical plating time. Then, the electroplated ceramic specimens were soldered with 60 wt.% Sn-40 wt.% Pb solder in active colophony. The highest shear strength was acquired after the heat treatment at 170℃ for 15 min. The joint fractures mostly propagated along the interface between the ceramics and the Ni-P coating, with some fracture in both the ceramics and the Ni-P coating near the interface and some along the interface between the Cu and Ni-P coatings. The results show that ceramic surface roughness and the chemical plating parameters influence the coating quality, and that suitable heat treatment before the soldering also improves the adhesion between the ceramics and Ni-P coatings, thus strengthening the joints.     

棕榈油对淀粉物料微波膨化的影响

研究了棕榈油对淀粉物料微波膨化产品的质量和质构的影响。结果表明，棕榈油的添加减弱了微波的加热效果，且随着油含量的增加，温升速率逐渐减小，含油物料微波膨化过程中的加热段延长了10－20s，膨化段和固化段相应推迟10－20s，物料的膨化速度随着含油量的增加而减小。微波处理90s后，对照样及含油量为0.05,0.10,0.15和0.20mL/g的产品其膨化率分别为4.44,4.17,3.43,2.88和2.10。随着含油量的增加，产品的孔隙率逐渐增大，在含油量大于0.15mL/g后，这种增加程度加深，产品的质构变粗糙，向淀粉物料中添加棕榈油可以改善微波膨化产品的脆度，且在添加量为0.05mL/g时产品的硬度最小。添加棕榈油后的产品色泽与油含量有关，与微波膨化无关。     

微波辐射合成7-羟基-4-甲基香豆素

以浓硫酸为催化剂，采用微波辐射技术，由间苯二酚与乙酰乙酸乙酯缩合制备7－羟基－4－4甲基香豆素。结果表明，微波辐射合成7－羟基－4－4甲基香豆素的最以应条件为：间苯二酚5.5g，乙酰乙酸乙酯6.8ml，浓硫酸1.5ml，微波功率240W，微波辐射时间6min，产率84．1％，不采用微波辐射，反应时间大于10h，产率78％，红外光谱分析表明，7－羟基－4－4甲基香豆素的特征峰与7－羟基－4－甲基香豆素的各官能团的吸收峰吻合，测定7－羟基－4－甲基香豆素的熔点为189－192℃。     

一种减小反射式0－π调相器尺寸的新方法

在微波频率低端，按常规方法研制的调相器尺寸是大的，该文采用金属化孔和改变调整元件，结果证明，在不降低性能指标的情况下，可以减小调相器的尺寸。     

单涂层吸波材料的优化设计及偏差研究

本文通过对单涂层吸波材料内电磁波传输损耗机理的细致研究，提出了单涂层吸波材料优化设计的两项原则。结合具体实例详细说明这两项原则的具体应用，最后讨论涂层电磁参量在偏离匹配条件的情况下，对涂层吸波性能影响的具体结果分析。图３．表１，参３。